Leading 10 common forklift accidents ， forklift operation should pay attention to these issues ！.
Leading 10 common forklift accidents ， forklift operation should pay attention to these issues ！.
Blog Article
Do not underestimate the forklift at work. If the operation is not good, there will be severe crashes in mins, and there are several accidents involving forklifts.
Case 1: The forklift cargo obstructed the driver's sight, and the person in front could not be found, resulting in a moving crash.
Instance 2: In order to keep the equilibrium of the forklift when raising heavy products, the workers used their body weight as the counterweight, which almost caused casualties.
Instance 3: The size of the forklift freight surpasses the permitted width of the route and holds on the roadside rack, which practically causes an accident.
Instance 4: Forklift is speeding up and rolls over during a turn.
Case 5: The forklift vehicle driver did not see the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the employees unlawfully, the forklift chauffeur does not wear the safety belt, the forklift lifter drops and the chauffeur is crushed when the forklift surrender.
Situation 7: The forklift driver did not put on a seat belt and fell from the lorry when it rolled over and was crushed.
Forklift procedure ought to take note of these issues ：.
Begin.
1. Before beginning, observe the surroundings, and after validating that there are no obstacles that prevent the security of driving, honk the horn initially and then begin.
2. For cars with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge must be secure prior to starting.
3. When the forklift begins with a tons, the vehicle driver must first verify that the lots is steady and reliable.
4. The begin must be sluggish and steady.
Driving.
1. When driving, the height in between the bottom end of the fork and the ground should be maintained 300mm-400mm, and the pole ought to be slanted in reverse. .
2. Do not lift the fork too high when driving. When going into and leaving the work site or while driving, take care that there will be no challenges overhead. When the load is traveling, the fork needs to not be raised too expensive, which will certainly affect the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the typical driving placement before driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal should be issued first. High-speed doglegs are banned. High-speed sharp turns will trigger the automobile to shed side stability and tip over. .
5. When the forklift is downhill, it is strictly prohibited to shut off the fire and slide, and it is restricted to brake suddenly while driving with loads unless there are special scenarios.
6. When the forklift is running, it needs to comply with the website traffic rules in the factory and must keep a certain safety distance from the car in front. .
7. When the forklift is running, the tons should remain in the most affordable placement that does not prevent the driving, and the gantry needs to be properly slanted back. The lots will not be elevated other than when piling or packing. .
8. The height of the load should not block the driver's view. In unique circumstances, when the item impacts the forward vision, drive at a low rate when reversing.
9. It is prohibited to switch on the ramp, nor to drive throughout the ramp. .
10. The secure driving rate of the forklift in the manufacturing facility area is 5 km/h, and it should drive safely at a reduced rate when going into the production workshop location. .
11. When the forklift is raised, lifted or driven, it is forbidden for employees to depend on the fork to hold products and play a balancing duty. .
12. If issues are discovered, they will be fixed and reported in a timely manner, and they will certainly never operate with ailments or hide them.
loading and unloading.
1. When fork-loading things, the distance in between both forks should be readjusted as needed to make the load of both forks balanced and not manipulated, and one side of the product should protest the rack. .
2. It is restricted to collaborate with a single fork or make use of a fork top or pull. In unique scenarios, safety indication should be established to remind bordering pedestrians. .
3. In the process of loading and dumping products, the forklift has to be braked with the brake. .
4. The rate of the car need to be sluggish and constant. Beware not to roll the wheels on the dunnage, so as not to extend the rolled objects and injure people. .
5. When utilizing a fork to fork the goods, the fork should be as deep as possible under the lots, and it ought to be kept in mind that the fork tip must not touch various other goods or items. The lots ought to be maintained with minimal back tilt of the gantry to ensure that the lots does not slide backwards. The pole can be slanted forward somewhat when the lots is lowered to enable very easy positioning of the Stand-on Electric Pallet Stacker load and extraction of the forks. .
6. It is restricted to fork items at high speed and hit difficult things with the fork head. .
7. When the forklift is working, it is restricted for individuals to loaf the fork, so as to stay clear of the collapse of the goods and hurt people. .
8. Overwhelming is forbidden, and it is banned to use forks to lift workers to participate in high-altitude procedures to stay clear of high-altitude dropping accidents. .
9. It is not allowed to use the brake inertia to slip, put, round or roll items. .
10. It is not enabled to utilize forks to choose, transform pallet dump.
Leaving .
1. It is restricted to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you have to dump the goods or reduced the fork structure.
2. Draw the hand brake handle to dead or dispirit the hand brake button.
3. The engine is switched off and Electric Forklift Truck for Warehouse the power is removed. (Except for unique conditions, such as the vehicle driver does not leave the lorry's view and does not go beyond 1 min).
4. Eliminate the secret. .
Forklift Operation Precautions.
1. Before and after the forklift operation, the look needs to be examined, and gas, lubricating oil and cooling water should be included.
2. Examine the security performance of starting, running and stopping.
3. Examine whether the lights and horn signals are total and efficient.
4. During the procedure of the forklift, inspect whether the pressure and temperature are regular.
5. After the forklift is running, the exterior leakage should additionally be examined and the seals should be changed in time.
Forklift Safety Operation Specifications.
1. You need to check prior to leaving the auto;.
2. When you come across somebody in front of you throughout driving, you ought to send a signal at a distance of 5 m;.
3. The driving rate in the factory does not go beyond 5 km/h;.
4. When driving, the nadir of the cargo need to be 0.3 m ~ 0.4 m above the ground;.
5. The turning must not be too sharp to stop the tendency of "free switching";.
6. Running up and down the incline ought to be slow-moving and uniform, and no turning on the slope is allowed.
7. Do not drive throughout the slope. When the gradient is greater than 10%, the automobile should be driven in reverse when going downhill;.
8. When the forklift employees carry the goods and move on, if they encounter big or heavy products and most likely to the chauffeur's view, they ought to take the turning around exercise
.
The "Eight Prohibitions" must be adhered to in the operation.
1. Solitary fork procedure is not allowed.
2. It is not enabled to raise the goods for long distance driving.
3. It is not permitted to grab the goods by handing over the pallet with the fork.
4. It is not permitted to straight shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not permitted to use inertia force to grab the goods.
6. It is not allowed to use stopping pressure to expatriation round or easy-to-roll objects.
7. It is not enabled to bring individuals to work with the pallet or fork, and it is strictly forbidden to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Car parking is not permitted under the list below problems.
1. Contours, slim roads, railway crossings;.
2. Sections with a longitudinal slope above 5%.
3. When there is an barrier on one side of the roadway, the contrary side of the section with the same length as the challenge must be within 20 meters at each end.
Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844